Messages

1

Vintage, PVT & 2 Litre Forum / Re: ACOC National Day May 26th

« on: April 02, 2024, 09:53:24 »

I plan to be there, I hope so as I am the organiser! Yes I am bringing my two Bucklands along with my Gold 2 Litre, I believe Mike Smith and Colin Naish are bringing their Bucklands, I hope many more 2 Litre and Bucklands will come to celebrate 75 years of the club. I look forward to meeting everyone. Best regards Leo

2

Vintage, PVT & 2 Litre Forum / Re: AC Buckland in huge barnfind!

« on: December 07, 2023, 19:55:37 »

I have seen this car before, it doesn't have the normal AC motif on the radiator cowl, just a badge. Also the frontal treatment of the car is very different. The front wings and radiator cowl are one piece, the cowl which is normally Brass could possibly be aluminium.  Normal Buckland's and 2 Litre Saloons have piping joining the panels. I have seen one other Buckland like this, is was a Maroon coloured car in very poor condition, I saw it back in the early 90's somewhere near the Liverpool area. I hope this info helps.

3

Vintage, PVT & 2 Litre Forum / Re: AC 2 Litre clutch problem?

« on: May 15, 2023, 14:02:49 »

Hi, I think you need to adjust the clutch pedal so as to give more clearance. The adjustment can be made under the car. You should be able to see a bracket attached to the bellhousing, you should be able to see how the adjustment should be made looking at the bracket as the clutch pedal is pressed down. Hope this info helps.

4

Vintage, PVT & 2 Litre Forum / Re: AC 2 litre wiring diagram

« on: March 15, 2022, 16:22:31 »

I will try to send you an attachment. if this fails please give me your email address and I will forward a copy of the early wiring diagram.
Regards, Leo

5

Ace, Aceca & Greyhound Forum / Re: AC Ace AEX-1010 Found

« on: August 30, 2021, 16:45:10 »

Ok, keep in touch and lets see what happens.

6

Ace, Aceca & Greyhound Forum / Re: AC Ace AEX-1010 Found

« on: August 28, 2021, 14:22:00 »

Hello Fastpace, You have a very interesting project. I have available a completely  new rebuilt CL AC 2 litre engine which I now do not need, this might be of interest to you if you want to bring the car back to original. Let me know if you would like further details.
Leo

7

Ace, Aceca & Greyhound Forum / Re: Gearbox help

« on: August 27, 2021, 19:56:33 »

Hello Paul , I had the same problem many years ago, it was the clutch release bearing that had worn down, no matter what adjustments we made it came down to the bearing. I hope this helps

8

Vintage, PVT & 2 Litre Forum / Re: Buckland for sale

« on: June 05, 2021, 20:10:26 »

Hello David, sadly I did not post the information re this Drophead, my code is not ARCH, but the photo is interesting as the car uses the same rear side window treatment as the one off drophead with the larger boot and petrol tanks in the front wings.
Regards

9

Vintage, PVT & 2 Litre Forum / Re: Buckland for sale

« on: May 12, 2021, 18:41:53 »

Tom, did you receive my info on the updates I have found for the 2 Litre?
Regards, Leo

10

Vintage, PVT & 2 Litre Forum / Re: Buckland for sale

« on: May 12, 2021, 10:25:07 »

Yes all the above details are correct. This D/H/C is chassis number ELX 1102, engine UMB 1103, as can be seen the car is left hand drive and was originally sent to Auto Palace in Holland.

11

Vintage, PVT & 2 Litre Forum / Re: On the road, finally!

« on: March 24, 2021, 09:32:26 »

Hello, I read with interest your  problems with your carburetters. You mentioned that you have fuel misting at the entrance of the carbs. This normally happens when the valve timing is far advanced. For the vintage AC six the valve timing is inlet valve opens at 3.5 degrees after top dead centre and tappet clearance is .005 th.  Later engines have the inlet valve opening at 12 degrees before top dead centre and tappet clearance 20 th. It might be that if you adjust the timing chain sprocket one tooth it might help solve the fuel misting and the engine should run much smoother. These are only suggestions as I cannot know what way the engine has been set up re valve timing etc, but it's worth looking at to check all is well.

12

Vintage, PVT & 2 Litre Forum / Re: AC 2 litre brake master cylinder, assistance required.

« on: August 13, 2020, 10:00:57 »

Gary, I have looked at both cylinders small and larger bore, externally they are both the same size. The reason for the larger bore was because the rear brakes were changed to hydraulics thus the feeling was that a larger bore for pushing more fluid was required. However as you have fitted a servo and you are changing to hydraulic rear brakes, I would be inclined to try the system as it is and then make changes to the bore size afterwards. As I mentioned before the brake master cylinder is the same size, thus you could get the cylinder bored out and fitted with a new larger plunger and seal.
Hope this info helps. Regards Leo

13

Vintage, PVT & 2 Litre Forum / Re: AC 2 litre brake master cylinder, assistance required.

« on: August 09, 2020, 18:22:34 »

hello Gary, have you changed your phone number as it is telling me that it is not available. I have been trying to contact you re the brakes. If you know my e mail address please forward your new number. I am in France and will be here for approximately three months. Regards

14

Vintage, PVT & 2 Litre Forum / Re: Errol Flynn and his AC

« on: August 09, 2020, 18:19:45 »

I think I know who now owns this car, he lives close to Rotherham and the car has been almost restored.

15

AC Weller Engine / Water pump and Fan belt

« on: October 01, 2017, 14:08:36 »

it might be to obvious but there are four nuts holding the pump to the block, two nuts at the entry of water to the block and two nuts lower down on the pump body. As Robin says gentle heat helps plus use a socket bar pulling gently between the pump and the block, this normally does the trick