BE 646

[dkp_cobra]

As already suggested I think the hub had started to turn on the axle.




No way the remove the hub with a puller.

[dkp_cobra]

Currently, I am working on the rear brakes. It was nearly impossible to use the brake adjuster


After cleaning and greasing with copper paste it works like a charm




What looks like a pizza tray will be the new drum brake dust cover. The old ones (in the middle) have reached the end of there lifetime.

[James Eastwood]

Bravo, keep going.

One of my rear hubs had the same problem as yours, despite using a puller and a hydraulic press eventually I had to cut them apart and replace the parts which were very difficult to find.

[dkp_cobra]

The revenge of the mummy:




Fresh from the painter:

[dkp_cobra]

The hand brake cables are dead

 
especially the clamps

I got new hand brake cables from Brian Eacott

tried to make new clamps on the lathe

and it seems to work 

[dkp_cobra]

Work for the dumb: making header gaskets by drilling several small and big holes.

[dkp_cobra]

A look inside of the hand brake mechanism part of the slave cylinder.







The black parts are not rusty but black zinc-plated.

[AC Ace Bristol]

.
Peter
Great Thread been following from day ONE.
As you have the rear  wheel brake cylinders apart......  Tim Isles had some internal parts  made e.g.  the two small rollers and the two taper sliders which give you adjustment.
Not sure if you need replacement parts,  as these items are not readily available.  Tim had additional ones made .
Tim Isles Ace Bristol Registrar ... email:    tim_isles@hotmail.com
 Keith

[dkp_cobra]

Keith,
thank you for the advice. My parts are still ok. I will use them and in conjunction with the copper paste it works quite well.
Kind regards,
Peter

[dkp_cobra]

The orginal wheel nuts. 60 years of violance and abuse has left there marks.





Although I bought repro wheel nuts from MWS I decided to re-chrom the original wheel nuts. In agreement with the chroming-plating guy we decided not to remove every dent since the risk was revalant that the lettering would have been damaged. I think at the end I have some nice wheel nuts with some kind of patina. Also, the headlamp collars were re-chromed.










What a nice glittering christmas present 

[dkp_cobra]

Last action for this year: assembling the rear hubs with new bearings and sealings





The perfect time to replace the old bolts. Unfortunately, I wasn't able to find part threaded bolts with a length of 1 1/4" with a non-thread length of 1/2". So I bought 1 3/4" bolts, cut every one repaired the first two thread pitch of every bolt. What a funny work.


The break shoes got new brake linings. If you do this at home be aware that the two pots of the adjusting mechanism have a left and a right side. If you mix them up the brake shoes have a bigger diameter and the brake drum doesn't fit anymore.





I used the axle from Triple M. As mentioned above they changed their design a little bit. The main nut isn't self locking anymore but should be fixed with blue Loctite.


And finished. I hope that I will install them into the car next year. The special washer of the break drums are not rusty but black zinc-plated. Maybe not the best idea ...

[AE 501]

.....wie unsportlich, einfach den Entlüfternippel zu verlängern!

.....it's not fair but clever to have the bleeding nipple elongated!      My hands are not able to reach them in original shape ;-))

[dkp_cobra]

.....wie unsportlich, einfach den Entlüfternippel zu verlängern!

.....it's not fair but clever to have the bleeding nipple elongated!      My hands are not able to reach them in original shape ;-))

Honour, to whom honour is due. I thought this design is original. The car had the elongated bleeding nipples when I bought it.