Messages

1

Ace, Aceca & Greyhound Forum / Re: 1960 Ace/Aceca Rear Uprights

« on: December 30, 2023, 13:47:48 »

Hi, some time ago I needed new uprights for my 1955 Ace, AE103. Despite a long and fruitless search I decided to have two made. This entailed having patterns made and then cast. I have sold the patterns and a pair of uprights to Charlie Gray at Brooklands Cars, Weybridge, Surrey, UK. Perhaps he may be able to help.

2

Ace, Aceca & Greyhound Forum / Re: Fuel Pump location AC Engine

« on: August 07, 2023, 14:45:39 »

Hi, I have AE103 with AC engine. My SU fuel pump is mounted high in the left hand corner of the boot. It was originally located on the boot floor but  had it modified so that it was out of the way. Can send photo if required. Peter.

3

Ace, Aceca & Greyhound Forum / Re: ACE AE102

« on: February 15, 2023, 12:22:23 »

Keith, thanks for your reply. My contact details are:  p.bennett49@hotmail.com  or telephone 01606 882150 / 07976 255202.
Best regards, Peter.

4

Ace, Aceca & Greyhound Forum / Re: ACE AE102

« on: February 14, 2023, 14:02:13 »

Thanks Keith, do you have any contact details for Clive? I've looked in the club's membership list but his details are with held.

5

Ace, Aceca & Greyhound Forum / Re: ACE AE102

« on: February 13, 2023, 22:23:38 »

Keith, thanks for the information but who is Clive?

6

Ace, Aceca & Greyhound Forum / Re: Clutch plate stuck

« on: February 13, 2023, 16:13:46 »

Hi, start the car and get the engine up to temperature and turn off. Restart the engine with first gear engaged and the clutch depressed then accelerate hard, if this doesn't work try several more times. Make sure you're on a quiet road!! If you're not too sure ring me on 07976 255202 and I'll talk you through it. Best of luck.

7

Ace, Aceca & Greyhound Forum / ACE AE102

« on: February 13, 2023, 11:33:27 »

Does anyone know to the whereabouts or have any information about AE102? The only information I have is the factory record available on the ACOC website.

8

428 Frua Forum / 428 Frua chrome sill strip

« on: October 10, 2022, 14:45:29 »

I have a chrome sill strip for a 428. Right hand side, 155mm x 2mm. Not damaged and in reasonable condition. £150.
Tel. Peter Bennett 07976 255202 or email p.bennett49@hotmail.com

9

Ace, Aceca & Greyhound Forum / EARLY ACE DRIVERS DOOR

« on: September 08, 2021, 15:07:07 »

I know it's unlikely but does anyone have a new or very good condition drivers door for an early Ace? Is anyone making them?
Peter Bennett 07976 255202 email p.bennett49@hotmail.com

10

Ace, Aceca & Greyhound Forum / ACE / ACECA FRONT UPRIGHTS

« on: May 01, 2021, 12:45:14 »

I've had made, at great expense, a jig to fabricate Ace and Aceca front uprights. If anyone is interested in buying or hiring this jig please contact: p.bennett49@hotmail.com or phone 07976 255202.

11

General Forum / Re: 1937 with Cats Paw Engine

« on: July 02, 2020, 13:23:34 »

just noticed a fully re-built cat's paw engine, minus carbs, for sale at Brooklands Enginecraft, £15,000. tel (UK) 01380 584966.

12

General Forum / AC/ AC Owners Club sticker

« on: June 26, 2020, 18:45:17 »

Does anyone know where I can get a large (50cm + diameter) AC logo or AC Owners Club wall plaque, self adhesive sticker or a large flag for display purposes?
Please contact Peter Bennett  p.bennett49@hotmail.com   

13

Ace, Aceca & Greyhound Forum / ACE CASTOR / CAMBER ANGLES

« on: May 20, 2020, 19:34:45 »

Does anyone know what the original factory castor and camber angle settings were for for an early (1955) Ace? Please contact Peter Bennett, 01606 882150 or 07976 255202 email p.bennett49@hotmail.com

14

Ace, Aceca & Greyhound Forum / ACE / ACECA FRONT UPRIGHT JIG

« on: April 26, 2020, 15:12:36 »

Jig available for hire to manufacture Ace and Aceca front uprights.
Contact:  p.bennett49@hotmail.com

15

General Forum / FORUM LOG IN

« on: November 23, 2019, 11:26:26 »

It is impossible for me to log onto the FORUM. Despite being a fully paid up member of the ACOC the forum still doesn't recognise me and thinks I'm a GUEST. I have no problem with logging onto the web site, it's just the forum that's the issue. I've had some advice from Brian Mosely, thanks Brian, but this has proved to be ineffective. I've also been advised to buy a new computer but that seems a drastic solution to what should be a simple fix. I am currently using someone else's computer to write this post without any difficulty. Can anyone help please. Peter Bennett, tel: 01606 882150 / 07976 255202 or p.bennett49@hotmail.com