Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bennettpg49

Pages: [1] 2
1
General Forum / Re: 1937 with Cats Paw Engine
« on: July 02, 2020, 13:23:34 »
just noticed a fully re-built cat's paw engine, minus carbs, for sale at Brooklands Enginecraft, £15,000. tel (UK) 01380 584966.

2
General Forum / AC/ AC Owners Club sticker
« on: June 26, 2020, 18:45:17 »
Does anyone know where I can get a large (50cm + diameter) AC logo or AC Owners Club wall plaque, self adhesive sticker or a large flag for display purposes?
Please contact Peter Bennett  p.bennett49@hotmail.com   

3
Ace, Aceca & Greyhound Forum / ACE CASTOR / CAMBER ANGLES
« on: May 20, 2020, 19:34:45 »

Does anyone know what the original factory castor and camber angle settings were for for an early (1955) Ace? Please contact Peter Bennett, 01606 882150 or 07976 255202 email p.bennett49@hotmail.com


4
Ace, Aceca & Greyhound Forum / ACE / ACECA FRONT UPRIGHT JIG
« on: April 26, 2020, 15:12:36 »
Jig available for hire to manufacture Ace and Aceca front uprights.
Contact:  p.bennett49@hotmail.com

5
General Forum / Re: FORUM LOG IN
« on: November 27, 2019, 17:03:14 »
Thanks to those who have replied, I have now sorted the problem.

6
General Forum / FORUM LOG IN
« on: November 23, 2019, 11:26:26 »
It is impossible for me to log onto the FORUM. Despite being a fully paid up member of the ACOC the forum still doesn't recognise me and thinks I'm a GUEST. I have no problem with logging onto the web site, it's just the forum that's the issue. I've had some advice from Brian Mosely, thanks Brian, but this has proved to be ineffective. I've also been advised to buy a new computer but that seems a drastic solution to what should be a simple fix. I am currently using someone else's computer to write this post without any difficulty. Can anyone help please. Peter Bennett, tel: 01606 882150 / 07976 255202 or p.bennett49@hotmail.com

7
Ace, Aceca & Greyhound Forum / ACE/ACECA REAR UPRIGHTS
« on: October 10, 2019, 14:31:18 »
New ACE and ACECA rear uprights in SG (Malleable) Iron - this is a higher specification than ACs original material. The units are fully annealed and ready for machining, £1200 per pair. Contact Peter Bennett 01606 882150 / 07976 255202 / p.bennett49@hotmail.com

8
Ace, Aceca & Greyhound Forum / Test Post
« on: September 29, 2019, 09:56:24 »
This is a test post.

9
General Forum / Test Post
« on: September 29, 2019, 09:53:03 »
This is a test post.

10
I have 2 serviceable crankshafts and two serviceable cylinder heads for sale. The first crankshaft is for a UMB engine the second for a CL engine, measurements on request. The cylinder heads are for a UMB engine and a CL engine. £1500 each item. For more information please ring me on 01606 882150 or email p.bennett49@hotmail.com   

11
AC Weller Engine / CRANKSHAFTS AND CYLINDER HEADS
« on: February 20, 2019, 15:39:10 »
I have 2 serviceable crankshafts and 2 serviceable cylinder heads for sale. The first crank and head are for a UMB engine the second crank and head for a CL engine, crank measurements on request.  £1500 each item. For more information please ring me on 01606 882150 or email p.bennett49@hotmail.com   

12
Ace, Aceca & Greyhound Forum / Re: Ace front uprights
« on: February 13, 2019, 15:47:58 »
Thanks for that, I've already sent an email and am waiting for a reply.

13
Ace, Aceca & Greyhound Forum / Ace front uprights
« on: February 13, 2019, 10:20:25 »
Does anyone have a pair of new or un-used front uprights to fit an early Ace or know if anyone is re-manufacturing them?

14
Ace, Aceca & Greyhound Forum / AC engine number CL 2213W
« on: January 22, 2019, 13:24:34 »
Does anyone know to the whereabouts of AC engine number CL 2213W? It was originally fitted to AE 103.

15
Thanks Tony, will you let me have your email address please, the photos didn't come through.

Pages: [1] 2